Volume 11, Issue 4 (Journal of Control, V.11, N.4 Winter 2018)                   JoC 2018, 11(4): 37-46 | Back to browse issues page

XML Persian Abstract Print


Download citation:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:

Roozbehani S, Nazifi H, Saki S, Kanzi K. Identification and Torque Control of Claw Pole Eddy Current Dynamo meter . JoC 2018; 11 (4) :37-46
URL: http://joc.kntu.ac.ir/article-1-371-en.html
1- ACECR- K.N. Toosi
Abstract:   (6940 Views)

In this paper, the object is estimation and torque control of the claw pole eddy current dynamometer. The eddy current dynamometer is included DC excitation coil, poles and rotational cylinder that coupled to the electrical motor. Load testing of electrical motor in different operating point is done through torque control of dynamometer. The close loop system of eddy current dynamometer has two inner and outer control loops. In outer control loop, the torque should estimate. The torque estimation is presented as a function of DC excitation current and rotational speed. After that, as regards to comparison of reference torque and estimation torque, the reference current is determined. Finally, the control of DC current source is done to generate the reference current. Both controllers of loops are PI controller. The experimental and simulation results for 22.5 KW eddy current load is shown the efficiency of proposed estimation and control method. The implementing system is done by using the ARM-LPC-1788 micro controller.

Full-Text [PDF 920 kb]   (3268 Downloads)    
Type of Article: Review paper | Subject: Special
Received: 2016/05/11 | Accepted: 2017/08/29 | Published: 2018/01/14

References
1. Kh. Kanzi, A. Dehafarin, S. Roozbehani, M. Kanzi, Q.Vasheghani, "Novel Claw pole Eddy Current Load for Testing DC Counter Rotating Motor Part I: Construction," Journal of International Conference on Electrical Machines and Systems, vol. 1(3), pp.57-65, 2012. [DOI:10.11142/jicems.2012.1.3.321]
2. Kh. Kanzi, S. Roozbehani, A. Dehafarin, M. Kanzi, "Novel Claw pole Eddy Current Load for Testing DC Counter Rotating Motor Part II: Design and Modeling," Journal of International Conference on Electrical Machines and Systems, vol. 1(4), pp. 16-22, 2012. [DOI:10.11142/jicems.2012.1.4.412]
3. J.R. Bowler, T.Theodoulidis, "Boundary element calculation of eddy currents in cylindrical structures containing cracks," IEEE Trans. Magn, vol. 45(3), pp. 1012–1015, 2009. [DOI:10.1109/TMAG.2009.2012543]
4. D. Pusch, J. Smajic, Z. Andjelic, J.M. Ostrowski, "Comparison between BEM and classical FEM for a 3D low-frequency eddy-current analysis," IEEE Trans. Magn, vol. 46(8), pp. 2919–2921, 2010. [DOI:10.1109/TMAG.2010.2043514]
5. H. De Gersem, "Combined spectral-element finite-element discretization for magnetic-brake simulation," IEEE Trans. Magn, vol. 46(8), pp. 3520–3523, 2010. [DOI:10.1109/TMAG.2010.2043422]
6. E. Dlala, "Comparison of models for estimating magnetic core losses in electrical machines using the finite-element method", IEEE Trans. Magn, vol. 45(2), pp. 716–725, 2009. [DOI:10.1109/TMAG.2008.2009878]
7. J. Pippuri, A. Belahcen, E. Dlala, A.Arkkio, "Inclusion of eddy currents in laminations in two-dimensional finite element analysis", IEEE Trans. Magn, vol.46 (8), pp. 2915–2918, 2010. [DOI:10.1109/TMAG.2010.2044490]
8. S.E. Gay, M. Ehsani, "Parametric analysis of eddy-current brake performance by 3-D finite-element analysis", IEEE Trans. Magn, vol. 42(2), pp.319–328, 2006. [DOI:10.1109/TMAG.2005.860782]
9. H. Shin, J. Choi, H. Cho, S. Jang, "Analytical Torque Calculations and Experimental Testing of Permanent Magnet Axial Eddy Current Brake", IEEE Trans. Magn, vol.49 (7), 4152–4155, 2013. [DOI:10.1109/TMAG.2013.2250932]
10. R. Yazdanpanah, M. Mirsalim, "Axial-Flux Wound-Excitation Eddy-Current Brakes: Analytical Study and Parametric Modeling", IEEE Trans. Magn, vol.50 (6), 2014.
11. S. Sharif, J. Faiz, K. Sharif, "Performance analysis of a cylindrical eddy current brake", IET Electric Power Applications, Vol. 6(9), pp. 661–668, 2012. [DOI:10.1049/iet-epa.2012.0006]
12. S. Anwar, A Parametric Model of an Eddy Current Electric Machine for Automotive Braking Applications, IEEE Trans.Control system Tech, Vol.12, No.3, May 2004.
13. Zamani A. Design of a controller for rail eddy current brake system. IET Electrical Systems in Transportation. 2014 Jun; 4(2):38-44. [DOI:10.1049/iet-est.2013.0008]
14. Yazdanpanah R, Mirsalim M. Hybrid electromagnetic brakes: design and performance evaluation. IEEE Transactions on Energy Conversion. 2015 Mar; 30(1):60-9. [DOI:10.1109/TEC.2014.2333777]
15. S. Roozbehani, S. Saki, H. Nazifi, and K. Kanzi, "Identification and fuzzy-PI controller design for a novel claw pole eddy current dynamometer in wide speed range," in Electrical Engineering (ICEE), 2016 24th Iranian Conference on, 2016, pp. 1038-1042. [DOI:10.1109/IranianCEE.2016.7585674]

Add your comments about this article : Your username or Email:
CAPTCHA

Send email to the article author


Rights and permissions
Creative Commons License This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

© 2024 CC BY-NC 4.0 | Journal of Control

Designed & Developed by : Yektaweb